Getting Started with Plumber's Essentials for Bathtub Installation
Getting Started with Plumber's Essentials for Bathtub Installation
Blog Article
Were you interested in selective information around A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably difficult task. If the old bathtub is conveniently obtainable, the job can relocate rapidly; if you need to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's skills, although you will need an assistant to move out the old tub and also set in the brand-new one. Ensure you have qualified yourself for the task and also fit trying it. Instead of employing a contractor to take over a halfway-completed project, it is better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This article will help you mount a new bath tub in your bathroom if you have actually currently bought a brand-new bathtub as well as do not need to change the setup of your previous water system pipes.
Your devices as well as product checklist need to make up the following:
Preparing for the Setup
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the tub in the required placement. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bath tub until the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the water system and check all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the bathtub as well as additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the tub has been made use of a minimum of when as this will resolve it into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the tap and the sink. Protect the tap in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind must be linked to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, causing the water to penetrate the wall between the bathroom and the tiling, resulting in complications with moisture and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads on How to Install a Bathtub, I was thinking sharing that excerpt was a smart idea. Enjoyed reading our write-up? Please share it. Let somebody else check it out. Thank you for your time. Come back soon.
For instant fixes, dial! Report this page